- Igt S+ Slot Machines For Sale
- Slot Machine Games
- Igt S+ Slot Machine Parts
- Igt S Slot Machine Main Board 75511500 Dimensions
Igt S+ Slot Machines For Sale
When replacing your slot game kit or converting to a different game some kits will include only 2 pieces of glass while others will include all 3 pieces. It really just depends on the game theme. Begin the conversion by removing the top glass. This is done by opening the slot machines main door and carefully lifting up on the glass holder bracket or player tracking bracket that holds the glass in place. Install the new upper glass. If your new kit included the (Reel) glass proceed to remove the old one by removing the florescent lamp bulb and then removing the 3 7/32' florescent fixture screws and finally the fixture itself. Once the fixture is removed you should be able to carefully slide the reel glass out of the machine by grabbing the old reel glass on both sides and carefully wiggle it out of the lower holder and replace it with the new piece of glass. (Be sure that all of your glass decal stickers are securely attached to the new glass pieces before installing the light fixture. Next, the belly or lower glass is replaced by first locating the belly door release knob found on the main door of the machine. Just pull the knob straight out to the right and the belly door will flip down allowing you to remove the the belly glass assembly. You will need to remove the 4 7/32' nuts securing the lighting fixture and then carefully slide the old glass out of the machine. When installing the new belly glass be sure that it is facing right side up with the belly door in its closed position before you tighten up the 7/32' nuts.
Replacing the Slot Reel Strips
Lay out the new strips on a flat surface and take a comparison look at the strips different symbols. If they are all the same and all the symbols line up with each other then you do not need to be concerned with which strip goes to which reel. If however, any strips are different from each other than you will need to install them in the numerical order that specified in the PAR sheet for the game.
Slot Machine Parts for Bally and IGT Slot Machines. Antique 1940's Slot Machine MILLS DIAMOND FRONT 5 CENT Chrome Face w/Jackpot. 3D Pandora's Box 2260. This is a used igt board for an igt slot machine. Used S+ board is a great replacement board for your machine. We have plenty of used s plus boards with 'good condition' in stock. Product information Buy Sell Trade & Repair Slot Machines and Casino Gaming Equipment and Tables.
The Reel Strips should also be numbered either on the bottom of the strips or on the back side. The numbers on the reel strips will indicate which strips install into which reel assembly either (1, 2 or 3) depending on your game conversion theme. (Refer to your game theme PAR sheet for specific details) The reel strips will have small notches cut in them at the bottom of the strip. The notches must align with the notches that are molded into each reel basket.
In most cases (Not all) the reel strip showing the lowest number will be installed in the left reel assembly (#1) and the next higher # reel strip will install in the middle reel, etc. If your reel strips contain different symbols on them this rule may not apply.
Locate the notches at the bottom section of the reel strips. You must install the strips aligning these notches with the notches in the reel baskets. The easiest way to do this is to place a reel strip into the left side groove of the basket that it is to be installed into and hold the strip at a 45 degree angle to the basket with one hand and use the other hand to rotate the basket slowly until you feel it catch on the notch. Then, proceed to roll the strip around the back side of the basket and as you do tuck both sides into the grooves of the basket until you come back around to where you started. At this time you want to make sure that the end of the reel strip overlaps the other end of the strip and that they are seated together with the self adhesive sticky surface on the inside of the strip. (You may have to use clear scotch tape to secure the strip to itself. If you did this correctly, you will not be able to see the notches in the strips after you are finished and the reel should spin straight and true. numbers on the bottoms or back sides of the strips so that they are installed in the correct reel.
If you change your 'Game' eprom you will likely loose the function of the machines bill acceptor and it will require a special set chip to re-activate it. Because of this, most game conversion kits do not require nor include a new game chip as part of the conversion.
Install the new IGT S+ 'REEL' Eprom chip that was included with your game kit in the same direction as the old one that you just removed. This means the notch in the chip must install in the same direction. Use caution when installing the chip so that you do not fold over any of the chips pins .Go slowly and re-check all the legs as you go and again after wards. If one or more of the legs do get bent, you must straighten it before proceeding. Next, push down on the top of the chip firmly until the chip is seated all the way in its holding socket. If you were instructed to also change the 'GAME' chip with your new kit now is the time to do that following the same guidelines as above. You are now ready to install the system board and bring up the machine to set the games options.
Install IGT S+ Slot Machine MPU Board
Make sure you reinstall the main board the same as it was removed. The board must align on both sides of the board holder. It also must be completely seated down against the lower board. Use care to be sure both sides are square during this procedure and Don't use excessive force when seating it down against the bottom board or you risk damaging the pins that are located on the bottom.
Initialize IGT S+ Slot Machine
After installing the main system board. Install the hopper and turn the power switch on. The machine should boot and display a code '61' in the winners paid window. - (You may see a 65, 66 or 67 in the window instead) See the below illustrations and pictures to see what you need to do for each code displayed:
Press and hold the test button until you hear a 'Ding' and see a 61 - 1 code displayed
If you see a '65, 66, or 67'code after making a chip change - Power off the machine, then back on. You should then see a 61 displayed in the winner paid window.
Once you get a 61- 1 close door completely and turn the rest key one time to initialize your new slot game. This is the final step in the conversion process. Congratulations! You did it!
Slot Machine Games
IGT S-Plus, S2000 or S2000 Vision
IGT model identification one machine is always confusing. They look so much alike that if you don’t know what to look for then you probably just guess or go by what someone tells you that it is. Many of the games are available in more than one model of machine so knowing which machine is which is important.
S-PLUS – There are 3 ways this machine can be identified. Usually these machines have six serial numbers on the right side The ‘Winner Paid’ and ‘Credits’ meters are to the left of the center of the reel glass. The also have the motherboard behind the hopper.
S-2000 – Almost any part of these machines can be upgraded, doors,bill and I think you can get different colored speakers. You can identify these by the long meter to the left of the reel glass, the serial number is seven numbers on the side or you may notice that these machines are capable of taking multiple denominations ($.25 or $.50) there reel glass will show these markings.
Vision – The Vision games machines look identical to S-2000s except that the have a monitor on the upper glass and a plays a bonus game. The monitor appears flush with the glass and not bordered with lights.
Igt S+ Slot Machine Parts
Reel Touch – These machines have a round top and inset monitor with an lighted frame. These are 5 reel machines and the reels are back lit have five back-lit reels. The reel-touch are similar in appearance to the S- 2000 many of the internal parts are the same.
Igt S Slot Machine Main Board 75511500 Dimensions
I-Plus – Typically you will find these as either a video slot or video poker. The Game King is an example of a multi-game machine built on the I-Plus platform. They are identifiable by their round top, large video display. The display is a touch screen and used to select the games